Please note this guide is updated regularly – Last Updated 5th June 2016
If you follow this guide and want to add or contribute to pictures/guide, please contact us. Continue reading “How to convert Baseflight To Cleanflight on Naze32” »

To Change the Eaching i6 Transmitter settings, Hold the yaw trim to the right, the roll trim to the left and turn on the transmitter. You can then enter settings by holding down ok on the Transmitter.

Eachine have been getting better at building Quads, but for the life of me I can’t understand why they still get so many basic things wrong.

Let me address some of them here as well as screenshots of all the default settings at the bottom. I will attempt to rectify and help Blade185 buyers fix most of the issues I have found. Continue reading “Eachine Blade 185 Review – Guide To How It Should of Been Setup With Cleanflight” »

So the other day I had a pretty big crash into mud..

The solution is to strip the motors apart, get a really hot container of water (boiling) and then jiggle it in until you get all dirt out.

I had to use a toothbrush in some parts (be careful) Continue reading “How to clean out your FPV Racing Motors from dirt or grass” »

For some strange reason which I have yet to identify… my ESC was powered when FC was hooked up to computer. This meant I could not drag sliders to MAX, plug in battery as when i dragged to max, the motor would spin and not engaged the calibration.

To solve this I had to do it a manual way using CLI commands. Continue reading “How to calibrate ESCs when your Flight Controller powers the ESC” »

Usually F3 boards will come with Cleanflight 1.9.0 and there has been a tonne of updates since then.

I tried flashing and kept getting the error “Communication with bootloader failed”

Download the latest Betaflight or Cleanflight from the website (at this time it is betaflight_2.6.1_SPRACINGF3.hex)

Then goto firmware on clean flight configuration tab and make sure you load the file then change the settings to this

-Full chip erase.

-Manual baud rate 256000.

Flash and it should work!

One of our Customers Gavin came across a slight issue when he had a crash and realised it can be fixed in future by adding a small washer. If you get your Falcon 250 ,you may want to put this washer in.

Continue reading “Eachine Falcon 250 PCB Shorting Issue and How To Fix” »

1x Bolt210 Black Ops Frame with 4 Inch arms
1x CC3D Flight Controller running Betaflight 2.6.1
1x Matek PDB BEC-5V/3A LED Lighting Control Tracker Low Voltage Alarm LED & POWER HUB 5in1
4x Xnova 2206-2500kv Multi-Rotor Racing Pack (Set of 4)
4x FVT Littlebee 30a ESC BHHELI
1x Aomway T25 5.8GHz Selectable 25/200mW 40CH FPV Tx
1x AOMWAY CBA004 Antenna Extension Adapter Cable RP-SMA-MALE to SMA-Female Plug/SMA JACK 80mm
1x Foxeer HS1177 XAT600M DC5V-22V 600tvl Sony Super HAD CCD FPV Camera IR Block 2.8mm Lens PAL

1x FrSKY Taranis X9D Plus Mode 2 2.4Ghz Digital Telemetry Radio System With Alluminium Case
1x FrSky XSR 2.4GHz 16CH ACCST Receiver with S-Bus and CPPM Continue reading “Bolt 210 Black Ops 4 Inch Arms Build Log” »

1x Covert230 Frame made out of HDPE (high density polyethylene) – By Chris Matvejev
1x CC3D Flight Controller running Betaflight 2.6.1
1x MXK Power Distribution Board PDB with OSD BEC Output 5V 12V 3A LC Filter for CC3C Naze32 F3
4x Cobra 2204/2300kv Motors
4x FVT Littlebee 20a ESC BHHELI
1x Aomway T25 5.8GHz Selectable 25/200mW 40CH FPV Tx

1x FrSKY Taranis X9D Plus Mode 2 2.4Ghz Digital Telemetry Radio System With Alluminium Case
1x FrSky XSR 2.4GHz 16CH ACCST Receiver with S-Bus and CPPM Continue reading “Yellow Bumble bee Build Log” »